Clifford SmartWindows 4 Uživatelský manuál stáhnout pdf (Strana 9)

User-Programmable Features

User-Programmable Features (1 Chirp = OFF, 2 Chirps = ON)

Fea ture

Select

Unmarked 1 Unmarked 2 Unmarked 3 Unmarked 4

✱ 1

Add New Remote

NOTE 1

Chirps

(Off/On/Quiet)

(1 chirp/2 chirps/3 chirps)

AutoArming

(Off/On)

Arm/Disarm with

Secondary Remote

NOTE 5

✱ 2

Personalized Siren Sounds*

NOTE 2

NOT USED

AutoArm & Lock

(Off/On )

Trunk Release with

Secondary Remote

NOTE 6

✱ 3

Play Siren Sounds*

Remote Valet Feature

(On/Off)

NOT USED

Silent Arm/Disarm with

Secondary Remote

NOTE 6

✱ 4

Siren Duration

(30 /60/90 seconds)

AutoStart

Neither/Battery/Temperature/Both)

(1 chirp /2 chirps/3 chirps/4 chirps)

(Requires IntelliStart 4)

FACT

(Off/On)

NOT USED

✱ 5

AutoLock

(Off/On/RPM)

(1 Chirp/2 Chirps/3 Chirps)

(IntelliStart 4 required for RPM

dependent door locking)

NOT USED

Remote Start with

Secondary Remote

(Requires IntelliStart 4)

NOTE 6

✱ 6

AutoUnlock

(Off/On)

Clear All Remotes

NOTE 4

NOT USED

Window Rolldown/Venting

with Secondary Remote*

(*Requires

SmartWindows 4)

NOTE 6

✱ 7

Re set All to Fac tory Set tings

(ex cept re mote controls and

valet code)

NOTE 3

Valet Code

SHOULD ONLY BE PROGRAMMED

BY THE VEHICLE OWNER

NOT USED

Remote Valet Mode

with Secondary Remote

NOTE 6

*Requires SmartSiren 4

NOTE 1: Press the button on the remote to be programmed, you will hear one chirp. Press the button again, you will hear

two chirps.

NOTE 2: When this feature is selected, siren sound 1 will play for five seconds. Press ✱ to turn the siren sound off, press

unmarked to activate the sound. Next, siren sound 2 will play for five seconds. Press ✱ to turn the siren sound off,

unmarked to activate it. This system will cycle through all six siren sounds, repeat this procedur e for each sound.

NOTE 3: You will hear two chirps when all features are reset.

NOTE 4: When you hear two chirps, all remote controls will have been erased from the system memory. You mu st now add

the new and/or existing remote controls to the system (i.e., AutoProgram each remote that will be u sed with the Concept

100).

NOTE 5: Programs a remote control from any other Clifford system (that uses ACG 2 technology) to arm or di sarm the

vehicle. For instance, to set the button + ✱ combination of the other car’s master remote control to arm/disarm the

system, select column 4, row 1, then transmit the + ✱ button combination from the remote you are programming. The

system will respond with one chirp. Immediately press the button combination a second time. The sys tem will respond with

two chirps. The other vehicle’s remote will now arm/disarm the system by pressing the and ✱ buttons simultaneously.

NOTE 6: This feature can be controlled by a secondary remote or any remote control of any other ACG 2 syst em, after that

remote has been programmed to arm/disarm this system. Select the row and column number, then transm it the unused

button on the other remote that you want to use to perform that function. The system will respond w ith the same number

of chirps as the row number. Please note that you must first set a button on the remote that will a rm/disarm the system

(column 4, row 1) before these others will be accepted.

Con cept 100/199 9

1 2 3 4 5 6 7 8 9 10 11 12 13 14

Komentáře k této Příručce

Žádné komentáře

Clifford SmartWindows 4 Uživatelský manuál Strana 9

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Clifford SmartWindows 4